Isuzu I 280 ABS Wheel Speed Sensor in US

Your Isuzu I 280 ABS wheel speed sensor is the component that makes anti-lock braking possible on your I 280. It monitors the rotational speed of each wheel in real time and sends that data to the Isuzu I 280 ABS control module, which uses it to prevent wheel lockup during emergency stops. When a sensor fails on your I 280, your ABS loses the input it needs. On wet, icy, or gravel road surfaces, the difference between a controlled stop and a skid can come down to whether your Isuzu I 280 wheel speed data is reaching the module.

What Is the ABS Wheel Speed Sensor on Your Isuzu I 280

The ABS wheel speed sensor on the Isuzu I 280 is an electromagnetic or Hall-effect sensor mounted near each wheel hub or bearing assembly of your I 280. It generates an electronic signal as a toothed reluctor ring rotates past it, producing a frequency the I 280 ABS module interprets as wheel speed. On most modern Isuzu I 280 vehicles, this same data feeds the traction control system, electronic stability control, and electronic brake force distribution, making a functioning wheel speed sensor critical to the safe operation of multiple I 280 systems simultaneously.

Signs of a Failing ABS Wheel Speed Sensor on the Isuzu I 280

• ABS warning light on your Isuzu I 280 dashboard, the most common first indicator of a failing sensor
• Traction control or stability control warning light illuminated alongside the I 280 ABS light
• ABS activating on your Isuzu I 280 during normal stops at low speed where it should not engage
• Complete ABS deactivation on the I 280, wheels lock under hard braking on wet or icy roads
• Speedometer on your Isuzu I 280 reading erratically or dropping to zero at speed
• Fault codes in the C0035 to C0050 range stored in the Isuzu I 280 ABS control module

Passive vs. Active ABS Sensors for the Isuzu I 280

GeoBrakes stocks both passive and active ABS wheel speed sensors for the Isuzu I 280. Passive sensors use an analog signal and are found on older I 280 vehicles and many trucks still in service. Active Hall-effect sensors require a small power supply and output a clean digital signal, offering greater accuracy at very low speeds. Active sensors are standard on most Isuzu I 280 vehicles manufactured after the mid-2000s and are required for full compatibility with modern I 280 traction and stability control systems.

Why GeoBrakes for the Isuzu I 280 ABS Wheel Speed Sensor

Signal accuracy matters as much as fitment with Isuzu I 280 wheel speed sensors. A sensor that generates the correct frequency for your I 280 ABS module ensures consistent ABS calibration, proper traction control thresholds, and accurate stability control response on your Isuzu I 280. Every sensor in the GeoBrakes catalogue is matched to the Isuzu I 280 through our vehicle selector, with front and rear positions listed separately to eliminate position errors on your I 280.

Frequently Asked Questions - Isuzu I 280 ABS Wheel Speed Sensor

Can I drive my Isuzu I 280 with a faulty ABS wheel speed sensor?

You can drive the Isuzu I 280 with a failed ABS sensor, but the anti-lock braking system on your I 280 will be completely disabled. On icy or wet American roads, this significantly increases stopping distances and the risk of losing steering control during hard braking on your Isuzu I 280. Replacing a failed sensor promptly is strongly recommended, particularly before winter.

How do I find the right ABS sensor for my Isuzu I 280?

Use the GeoBrakes vehicle selector and enter the Isuzu I 280 year, make, and model. The system displays only the sensors confirmed to fit the Isuzu I 280, with front and rear positions listed separately. Select the position matching the sensor you are replacing on your I 280 to avoid receiving the wrong unit.

Do I need to replace all four ABS sensors on my Isuzu I 280 at the same time?

No. ABS wheel speed sensors on the Isuzu I 280 are independent components and only the failed unit needs to be replaced. However, if your I 280 has high mileage and one sensor has failed, it is worth visually inspecting the connectors on the other Isuzu I 280 sensors for corrosion while the wheel is removed.