Bmw M135i ABS Wheel Speed Sensor in US

Your Bmw M135i ABS wheel speed sensor is the component that makes anti-lock braking possible on your M135i. It monitors the rotational speed of each wheel in real time and sends that data to the Bmw M135i ABS control module, which uses it to prevent wheel lockup during emergency stops. When a sensor fails on your M135i, your ABS loses the input it needs. On wet, icy, or gravel road surfaces, the difference between a controlled stop and a skid can come down to whether your Bmw M135i wheel speed data is reaching the module.

What Is the ABS Wheel Speed Sensor on Your Bmw M135i

The ABS wheel speed sensor on the Bmw M135i is an electromagnetic or Hall-effect sensor mounted near each wheel hub or bearing assembly of your M135i. It generates an electronic signal as a toothed reluctor ring rotates past it, producing a frequency the M135i ABS module interprets as wheel speed. On most modern Bmw M135i vehicles, this same data feeds the traction control system, electronic stability control, and electronic brake force distribution, making a functioning wheel speed sensor critical to the safe operation of multiple M135i systems simultaneously.

Signs of a Failing ABS Wheel Speed Sensor on the Bmw M135i

• ABS warning light on your Bmw M135i dashboard, the most common first indicator of a failing sensor
• Traction control or stability control warning light illuminated alongside the M135i ABS light
• ABS activating on your Bmw M135i during normal stops at low speed where it should not engage
• Complete ABS deactivation on the M135i, wheels lock under hard braking on wet or icy roads
• Speedometer on your Bmw M135i reading erratically or dropping to zero at speed
• Fault codes in the C0035 to C0050 range stored in the Bmw M135i ABS control module

Passive vs. Active ABS Sensors for the Bmw M135i

GeoBrakes stocks both passive and active ABS wheel speed sensors for the Bmw M135i. Passive sensors use an analog signal and are found on older M135i vehicles and many trucks still in service. Active Hall-effect sensors require a small power supply and output a clean digital signal, offering greater accuracy at very low speeds. Active sensors are standard on most Bmw M135i vehicles manufactured after the mid-2000s and are required for full compatibility with modern M135i traction and stability control systems.

Why GeoBrakes for the Bmw M135i ABS Wheel Speed Sensor

Signal accuracy matters as much as fitment with Bmw M135i wheel speed sensors. A sensor that generates the correct frequency for your M135i ABS module ensures consistent ABS calibration, proper traction control thresholds, and accurate stability control response on your Bmw M135i. Every sensor in the GeoBrakes catalogue is matched to the Bmw M135i through our vehicle selector, with front and rear positions listed separately to eliminate position errors on your M135i.

Frequently Asked Questions - Bmw M135i ABS Wheel Speed Sensor

Can I drive my Bmw M135i with a faulty ABS wheel speed sensor?

You can drive the Bmw M135i with a failed ABS sensor, but the anti-lock braking system on your M135i will be completely disabled. On icy or wet American roads, this significantly increases stopping distances and the risk of losing steering control during hard braking on your Bmw M135i. Replacing a failed sensor promptly is strongly recommended, particularly before winter.

How do I find the right ABS sensor for my Bmw M135i?

Use the GeoBrakes vehicle selector and enter the Bmw M135i year, make, and model. The system displays only the sensors confirmed to fit the Bmw M135i, with front and rear positions listed separately. Select the position matching the sensor you are replacing on your M135i to avoid receiving the wrong unit.

Do I need to replace all four ABS sensors on my Bmw M135i at the same time?

No. ABS wheel speed sensors on the Bmw M135i are independent components and only the failed unit needs to be replaced. However, if your M135i has high mileage and one sensor has failed, it is worth visually inspecting the connectors on the other Bmw M135i sensors for corrosion while the wheel is removed.