Bmw 135is ABS Wheel Speed Sensor in US

Your Bmw 135is ABS wheel speed sensor is the component that makes anti-lock braking possible on your 135is. It monitors the rotational speed of each wheel in real time and sends that data to the Bmw 135is ABS control module, which uses it to prevent wheel lockup during emergency stops. When a sensor fails on your 135is, your ABS loses the input it needs. On wet, icy, or gravel road surfaces, the difference between a controlled stop and a skid can come down to whether your Bmw 135is wheel speed data is reaching the module.

What Is the ABS Wheel Speed Sensor on Your Bmw 135is

The ABS wheel speed sensor on the Bmw 135is is an electromagnetic or Hall-effect sensor mounted near each wheel hub or bearing assembly of your 135is. It generates an electronic signal as a toothed reluctor ring rotates past it, producing a frequency the 135is ABS module interprets as wheel speed. On most modern Bmw 135is vehicles, this same data feeds the traction control system, electronic stability control, and electronic brake force distribution, making a functioning wheel speed sensor critical to the safe operation of multiple 135is systems simultaneously.

Signs of a Failing ABS Wheel Speed Sensor on the Bmw 135is

• ABS warning light on your Bmw 135is dashboard, the most common first indicator of a failing sensor
• Traction control or stability control warning light illuminated alongside the 135is ABS light
• ABS activating on your Bmw 135is during normal stops at low speed where it should not engage
• Complete ABS deactivation on the 135is, wheels lock under hard braking on wet or icy roads
• Speedometer on your Bmw 135is reading erratically or dropping to zero at speed
• Fault codes in the C0035 to C0050 range stored in the Bmw 135is ABS control module

Passive vs. Active ABS Sensors for the Bmw 135is

GeoBrakes stocks both passive and active ABS wheel speed sensors for the Bmw 135is. Passive sensors use an analog signal and are found on older 135is vehicles and many trucks still in service. Active Hall-effect sensors require a small power supply and output a clean digital signal, offering greater accuracy at very low speeds. Active sensors are standard on most Bmw 135is vehicles manufactured after the mid-2000s and are required for full compatibility with modern 135is traction and stability control systems.

Why GeoBrakes for the Bmw 135is ABS Wheel Speed Sensor

Signal accuracy matters as much as fitment with Bmw 135is wheel speed sensors. A sensor that generates the correct frequency for your 135is ABS module ensures consistent ABS calibration, proper traction control thresholds, and accurate stability control response on your Bmw 135is. Every sensor in the GeoBrakes catalogue is matched to the Bmw 135is through our vehicle selector, with front and rear positions listed separately to eliminate position errors on your 135is.

Frequently Asked Questions - Bmw 135is ABS Wheel Speed Sensor

Can I drive my Bmw 135is with a faulty ABS wheel speed sensor?

You can drive the Bmw 135is with a failed ABS sensor, but the anti-lock braking system on your 135is will be completely disabled. On icy or wet American roads, this significantly increases stopping distances and the risk of losing steering control during hard braking on your Bmw 135is. Replacing a failed sensor promptly is strongly recommended, particularly before winter.

How do I find the right ABS sensor for my Bmw 135is?

Use the GeoBrakes vehicle selector and enter the Bmw 135is year, make, and model. The system displays only the sensors confirmed to fit the Bmw 135is, with front and rear positions listed separately. Select the position matching the sensor you are replacing on your 135is to avoid receiving the wrong unit.

Do I need to replace all four ABS sensors on my Bmw 135is at the same time?

No. ABS wheel speed sensors on the Bmw 135is are independent components and only the failed unit needs to be replaced. However, if your 135is has high mileage and one sensor has failed, it is worth visually inspecting the connectors on the other Bmw 135is sensors for corrosion while the wheel is removed.